Marton 60373080 Concrete Cutting Machine 20 Inch With Benzine Engine 9HP + Diamond Blade 3 Mm 20 Inch Marton Orange 

Concrete cutter with 9 hp gasoline engine, MARTON is designed and manufactured with quality steel. It can be used for both diamond cutting blades and grooving cutting blades, with a cutting guide, making it convenient for the job and cooled by water, there is a 30-liter water tank to help moisten the cutting blade, there are 2 wheels, it is easy to move, suitable for cutting concrete or cement floors and grooving roads. 

• 20 Inch Concrete Cutter With 9 Horsepower Gasoline Engine
• Steel frame around the engine, anti-shock, easy to move.
• Threaded leveling steering wheel with level lock
• It has a cutting guide and a dust-proof rubber, making it convenient to use.
• Wheel Bearing 2 wheels for easy transportation.
• Comes with a 20-inch 3 mm thick diamond cutting blade.
• Compatible with diamond cutting blades and grooving cutting blades in sizes 16 inches, 18 inches and 20 inches.
• 30 liter water tank, removable for cleaning
• Suitable for cutting concrete or cement floors and grooving roads.
• 6 months warranty (according to manufacturer conditions)
• Orange

Technical Data

• Compatible with the engine : 9 hp gasoline
• Combination with Oil : Gasoline 95
• Compatible with Cutting Blades: 20 Inch Diamond Cutting Blade 3 mm Thickness / Grooved Diamond Cutting Blade 16 Inch, 18 Inch & 20 Inch
• Leveling Steering Wheel : Threaded Type with Level Lock
• Water Tank : 30 Liter Capacity (Removable for Cleaning)
• Wrenches : No. 34 and 27
• Product Dimensions (W x D x H) : 61 x 93 x 120 cm
• Weight without engine : 76 kg.

Preparing the appliance before use

1. Fill the engine oil to the required level before each use (the oil level is at the level of the last end of the oil bath).
2. Fill up with gasoline - gasohol except E20-E85
3. Check the platform retaining nuts and nuts for tightness.
4. Start the machine to see if it works normally.
5. Put the oil on the side of the air filter according to the specified limit to trap dust.
6. Fill the concrete cutting blade coolant in the coolant tank.

How to use

1. Start and warm up the appliance to idle for approximately 30 seconds before each use.
2. Replace the coolant valve of the concrete cutting blade.
3. Use the handle handle. Force the machine tightly, ready to make a concrete face cut.
4. Adjust the level by turning the steering wheel, adjust the height-low
   

• Cutting deeper, i.e., lowering the blade, by turning the steering wheel clockwise.
• Lifting the concrete cutting blade, e.g. adjusting the height of the blade by turning the steering wheel counterclockwise.

1. Cut concrete by accelerating the machine gently as needed. Do not accelerate the machine in a surge manner.
2. Use both hands to hold the left-right handles of the machine firmly. The concrete cutter must slowly move to the side in the desired direction.
3. Before turning off the engine, slow the engine down for about 30 seconds to 1 minute to allow the engine to release heat vapor.

MAINTENANCE

• Change the engine oil every 100 hours (No. 40 oil).
• Before use, always check the oil level of the engine (the oil level is at the level of the last thread of the oil bath).
• When discontinued, it should be stored in the shade and should not be exposed to the sun or rain.
• Check the belt pulley to ensure that it is always ready for use.
• Some parts have wear and tear over their life, such as throttle cables. Belts, bearings, wheels, etc., should be replaced when they begin to deteriorate with their condition.

Additional Recommendations

• If the device is used for several hours in a row, there should be a 1-hour break for every 3 hours of use, and it should not be used for more than 12 hours in a row.
• Do not add E20 , E85 fuel.
• You should use 4-stroke engine oil Benz No. 40.
• When moving, the fuel tank cap must be raised so that it is facing up at all times, do not lie on its side or lie down.
• Check the grease on the bearings before each use.

Note

• The price does not include the pick-up fee (for the lifting fee, please contact the after-sales service department at 1308).
• The colors of the products displayed on the website may vary depending on the color display settings of each screen.